Windows

Attribute ID: 202 (0xCA)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Data Address Mark errors S.M.A.R.T. parameter indicates the number of incorrect or invalid address marks.

Attribute ID: 203 (0xCB)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Run Out Cancel S.M.A.R.T. parameter indicates that an invalid error correction checksum was found during error correction.

Attribute ID: 204 (0xCC)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Soft ECC Correction S.M.A.R.T. parameter indicates the number of errors corrected by the internal error correction mechanism.

Attribute ID: 207 (0xCF)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Spin High Current S.M.A.R.T. parameter indicates the current needed to spin up the drive.

Attribute ID: 206 (0xCE)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Flying Height S.M.A.R.T. parameter indicates the height of heads above the disk surface. The low value of this parameter increases the chances of a head crash while a flying height that is too high increases the chances of a read/write error.

Attribute ID: 191 (0xBF)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu, Maxtor, Western Digital

Description

G-sense error rate S.M.A.R.T. parameter indicates the number of errors caused by externally-induced shock or vibration.

Attribute ID: 208 (0xD0)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Spin Buzz S.M.A.R.T. parameter indicates the number of retries during spin up because of low current available.

Attribute ID: 12 (0x0C)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu, Maxtor, Western Digital

Description

Power Cycle Count S.M.A.R.T. parameter is an informational parameter and indicates the count of full hard disk power on/off cycles.

Attribute ID: 7 (0x07)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu, Maxtor, Western Digital

Description

Seek Error Rate S.M.A.R.T. parameter indicates a rate of seek errors of the magnetic heads. In case of a failure in the mechanical positioning system, a servo damage or a thermal widening of the hard disk, seek errors arise.

Attribute ID: 9 (0x09)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu, Maxtor, Western Digital

Description

Power-On Hours (POH) S.M.A.R.T. parameter indicates a count of hours in power-on state. The value of this attribute shows total count of hours (or minutes, or seconds, depending on manufacturer) in power-on state. A decrease of this attribute value to the critical level (threshold) indicates a decrease of the MTBF (Mean Time Between Failures).

Attribute ID: 1 (0x01)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu, Maxtor, Western Digital

Attribute ID: 4 (0x04)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu, Maxtor, Western Digital

Description

Start/Stop Count S.M.A.R.T. parameter indicates a count of hard disk spindle start/stop cycles.

Each hard disk has its own limited number of these cycles depending on manufacturer. The maximum number of spinups/spindowns is called a threshold. When the parameter’s value drops down to the threshold, it means a hard disk is unhealthy.

If Acronis Management Server is installed on a guest operating system, which is backed up from the host, it will not display the correct task status on the dashboard

Acronis True Image Home 2010 is already included in Acronis Backup and Security 2010

Acronis Backup and Security 2010 does not overwrite the existing installation of usual Acronis True Image Home 2010 version with its own modified version of Acronis True Image Home 2010

Run the installation file, reboot the machine to finish the installation, enter the license key

Remove the grayed out machines from Acronis Management Server and then add them back to solve the issue

The location of your backup archive has changed or is unavailable

Acronis Backup & Recovery 10 can only back up to the root of Iomega REV drive.

Edit the archive.xml file to have the protection alert refreshed

As a workaround, uninstall the components that fail from Control Panel, and install them back using the installation file of build 11639.

Allow "System" rule 35 for Remote Desktop access

Pages

You are reporting a typo in the following text:
Simply click the "Send typo report" button to complete the report. You can also include a comment.
CAPTCHA
This question is for testing whether or not you are a human visitor and to prevent automated spam submissions.
8 + 3 =
Solve this simple math problem and enter the result. E.g. for 1+3, enter 4.