Windows

Attribute ID: 101 (0x65)

Hard drives, supporting this attribute

Maxtor

Description

Maximum FHC S.M.A.R.T. parameter is a Maxtor attribute (Flying Height control).

Recommendations

This parameter is considered informational by the vendor. Although degradation of this parameter can be an indicator of drive aging and/or potential electromechanical problems, it does not directly indicate imminent drive failure. Regular backup is recommended. Pay closer attention to other parameters and overall drive health.

Attribute ID: 103 (0x67)

Hard drives, supporting this attribute

Maxtor

Description

Translation Table Rebuild S.M.A.R.T. parameter is a Maxtor attribute.

Recommendations

This parameter is considered informational by the vendor. Although degradation of this parameter can be an indicator of drive aging and/or potential electromechanical problems, it does not directly indicate imminent drive failure. Regular backup is recommended. Pay closer attention to other parameters and overall drive health.

Attribute ID: 183 (0xB7)

Hard drives, supporting this attribute

Samsung, Western Digital

Description

SATA Downshift Error Count S.M.A.R.T. parameter is a Western Digital and Samsung attribute.

Attribute ID: 185 (0xB9)

Hard drives, supporting this attribute

Western Digital

Description

Head Stability S.M.A.R.T. parameter is a Western Digital attribute.

Recommendations

Although this parameter is not considered critical by the most hardware vendors, degradation of this parameter may indicate electromechanical problems of the disk. Regular backup is recommended. If no other (critical) parameters report a problem, hardware replacement is recommended on mission critical systems only.

Attribute ID: 186 (0xBA)

Hard drives, supporting this attribute

Western Digital

Description

Induced Op-Vibration Detection S.M.A.R.T. parameter is a Western Digital attribute.

Recommendations

Although this parameter is not considered critical by the most hardware vendors, degradation of this parameter may indicate electromechanical problems of the disk. Regular backup is recommended. If no other (critical) parameters report a problem, hardware replacement is recommended on mission critical systems only.

Attribute ID: 11 (0x0B)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu, Maxtor, Western Digital

Description

Recalibration Retries S.M.A.R.T. parameter indicates the number of attempts to calibrate the hard drive after the first unsuccessful try.

Attribute ID: 99 (0x63)

Hard drives, supporting this attribute

Maxtor

Description

Average FHC S.M.A.R.T. parameter is a Maxtor attribute (Flying Height control).

Recommendations

This parameter is considered informational by the vendor. Although degradation of this parameter can be an indicator of drive aging and/or potential electromechanical problems, it does not directly indicate imminent drive failure. Regular backup is recommended. Pay closer attention to other parameters and overall drive health.

Attribute ID: 13 (0x0D)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu, Maxtor, Western Digital

Description

Soft Read Error Count S.M.A.R.T. parameter indicates the number of uncorrected read errors reported to an operating system.

Attribute ID: 6 (0x06)

Description

Read Channel Margin S.M.A.R.T. parameter indicates a margin of a channel while reading data. Usually manufacturers do not use this parameter.

Attribute ID: 8 (0x08)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu, Maxtor, Western Digital

Description

Seek Time Performance S.M.A.R.T. parameter indicates the average performance of seek operations of the hard disk’s magnetic heads.

Attribute ID: 2 (0x02)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu, Maxtor, Western Digital

Description

Throughput Performance S.M.A.R.T. parameter indicates the general throughput performance of the hard disk.

Attribute ID: 221 (0xDD)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

G-Sense Error Rate (Shock Sense Error Rate for Hitachi) S.M.A.R.T. parameter indicates a number of errors resulting from shock or vibration.

Attribute ID: 231 (0xE7)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Temperature S.M.A.R.T. parameter indicates a drive temperature.

Attribute ID: 190 (0xBE)

Hard drives, supporting this attribute

Seagate, Samsung, Western Digital

Description

Temperature Difference from 100 (Airflow Temperature) S.M.A.R.T. parameter indicates the temperature of the air inside the Seagate and Samsung hard disk housing. The value is equal to [100 – specified by manufacturer temperature °C], which allows setting the minimum threshold.

Attribute ID: 194 (0xC2)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

HDA Temperature S.M.A.R.T. parameter indicates a hard disk drive current internal temperature. The raw value of this attribute shows built-in heat sensor registrations (in degrees centigrade).

Attribute ID: 226 (0xE2)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Load-in Time S.M.A.R.T. parameter indicates total time the heads are loaded.

Attribute ID: 228 (0xE4)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Power-Off Retract Cycle S.M.A.R.T. parameter indicates a number of times the head was retracted as a result of power loss.

Attribute ID: 227 (0xE3)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Torque Amplification Count S.M.A.R.T. parameter indicates a number of attempts to compensate for platter speed variations.

Attribute ID: 230 (0xE6)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

GMR Head Amplitude S.M.A.R.T. parameter indicates a head moving distances between operations.

Attribute ID: 240 (0xF0)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Head Flying Hours / Transfer Error Rate (Fujitsu) S.M.A.R.T. parameter indicates time spent during the positioning of the drive heads.

Attribute ID: 241 (0xF1)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Total LBAs Written S.M.A.R.T. parameter indicates a total number of LBAs written.

Attribute ID: 242 (0xF2)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Total LBAs Read S.M.A.R.T. parameter indicates a total number of LBAs read.

Attribute ID: 209 (0xD1)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Offline Seek Performance S.M.A.R.T. parameter indicates the seek performance of the hard drive during internal self tests.

Attribute ID: 250 (0xFA)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Read Error Retry Rate S.M.A.R.T. parameter indicates a number of errors found during reading a sector from disk surface.

Attribute ID: 220 (0xDC)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Disk Shift S.M.A.R.T. parameter indicates that a distance of the disk has shifted relative to the spindle, which could be caused by a mechanical shock or high temperature.

Attribute ID: 211 (0xD3)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Vibration During Write S.M.A.R.T. parameter indicates a vibration encountered during write operations.

Attribute ID: 222 (0xDE)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Loaded Hours S.M.A.R.T. parameter indicates a number of powered on hours. This value is constantly increasing (once per every hour).

Attribute ID: 223 (0xDF)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Load/Unload Retry Count S.M.A.R.T. parameter indicates a number of drive head enters/leaves the data zone.

Attribute ID: 224 (0xE0)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Load Friction S.M.A.R.T. parameter indicates the rate of friction between mechanical parts of the hard disk. The increasing value means there is a problem with the mechanical subsystem of the drive.

Attribute ID: 225 (0xE1)

Hard drives, supporting this attribute

Samsung, Seagate, IBM (Hitachi), Fujitsu (not all models), Maxtor, Western Digital (not all models)

Description

Load/Unload Cycle Count S.M.A.R.T. parameter indicates a total number of load cycles.

Pages

You are reporting a typo in the following text:
Simply click the "Send typo report" button to complete the report. You can also include a comment.
CAPTCHA
This question is for testing whether or not you are a human visitor and to prevent automated spam submissions.
6 + 0 =
Solve this simple math problem and enter the result. E.g. for 1+3, enter 4.